Cisco Fishing Systems
Adjustable Aluminum Rod Holders | Cisco Fishing Systems
Rod Holders

Rod Holders

Home > Shop > Rod Holders

What Makes Our Rod Holders The Best?

 When you purchase a Cisco rod holder you don't just receive a product, but a promise!  We are so confident in the workmanship of our rod holders that we back them 100% with our Lifetime Limited Warranty. 

 Our rod holders are taken to the limits in some of the harshest conditions on the water and are ruggedly constructed to withstand a lifetime of abuse.  Fishermen have found our products to be the BEST ON THE MARKET for Walleye, Salmon, Perch, Crappie, Striper and even Muskie fishing! 

 It adjusts in any direction with no tools in seconds and our exclusively designed cam-lock feature ensures that the tube of our rod holders will NEVER slip when secured in position, even when saltwater fishing! Guaranteed!

Upgrade to Cisco rod holders for a better fishing experience! What's Holding Your Rod?


Product Features

Please read the following features listed below to see why Cisco rod holders will be the last ones you ever own!

 Indexing Base

 Every rod holder comes with a spring loaded indexing base which allows the unit to rotate 360° (22 different positions) by simply lifting on the tube of the rod holder and turning it to your desired location.  We utilize a top and bottom indexing plate with twenty precision milled teeth on each plate for a tight engagement and no "slop".  Some of our competitors use only a single pin for their indexing stop and with the pin moving back and forth it can cause the hole in the aluminum to elongate over time.

Other manufacturers advertise that their rod holders rotate as well, but what they do not tell you is that tools may be required.  If you are looking for a feature comparable to our spring loaded indexing base you may find look alikes but this will come to you at a higher cost.

High Torque Tested

 When engineering our equipment no corners were cut to ensure maximum quality for a lifetime of use.  This stainless steel pin has been tested to withstand extreme amounts of torque and will never bend or wear. To prove this, our tubes are attached to our rod holders by means of a 1/2"  stainless steel stud.  This means that the tube is supported by a stainless steel pin which will tolerate 75,000 lbs per square inch before losing form while other manufacturers simply use a stainless dowell pin or screw.

Infinite Tube Positioning - Positive Locking Head

 While other manufacturers are complacent with offering 9 different tube positions for your rod holder, we are not.  Instead we have engineered an innovative design which allows you to adjust your tube to ANY angle between 0-90° (135° for cradles).  When engaged our padded lever tightly secures the tube in position with absolutely no "slop" or movement. 

Some of our competitors use only a single threaded screw for their indexing; over time with the pin moving back and forth it can cause the hole in the aluminum to elongate causing the tube to fit loosely in position.

Removable Tubes

 Cisco Tubes are REMOVABLE - Unlike the other manufacturers who crimp on their tubes, all of our tubes are left hand threaded onto a tube base so they can easily be removed whenever necessary. This is great for storage purposes, especially for rocket launchers when wrapping at the end of the season.

Aluminum Rod Holders

  • Bright Silver (standard color)
  • Bright Gold (up charge)
  • Bright Blue (up charge)
  • Bright Black (up charge)

No Plastic Parts

 We manufacture our mounts using only solid aircraft grade anodized aluminum, stainless steel screws, solid brass and bronze components; if you’re looking for plastic and other weak components then you must look elsewhere…you won’t find any of those parts here.

We offer a 100% guarantee on our rod holders! Every component in Cisco rod holders are made from SOLID aluminum and is precision machined to create the highest quality rod holder available on the market. There is no situation where plastic can ever be strong enough to hold the high amount of torque that serious anglers put on their rod holders. Cisco rod holders are built to last a lifetime of constant abuse.

No Rubber Caps Required!

Other major manufacturers simply saw off the tube and place a rubber cap over it to keep sharp edges from being exposed, but over time this cap, as you probably know will fall into the water.  At Cisco we machine a precision smooth radius on the ends of our rod holder tubes; this smooth radius protects your equipment and eliminates the nuisance of constantly replacing end caps.

 Perfectly Spaced Rod Holders

 Cisco rod holders are a standard 8-1/4" apart on the cross plates.  This position is vital to maintain a safe distance between rods to keep lines from tangling and rod from hitting each other.  Other manufacturers are much closer together. 

Build Your Own System or Check Out Our Pre-Assembled Packages

We understand that different types of fishing call for different types of rod holder setups and rigging, and this is why we allow our customers to build their own rod holder systems from the ground up.  Check out our pre-assembled packages for our most popular rod holder systems, or build your own to get you exactly what you need.  We offer a variety of mounting options from permanent to quick release, so be sure to choose the right system for your boat.

1. Choose the style and number of rod holders you want (tube, short cradle, long cradle).

2. Choose the corresponding cross plate (applicable only for double, triple or quad setups).

3. Choose the mount type  (permanent, track mount, thumbscrew or quick release)

 

Listed below are some of our most popular rod holder setups. Most often boats come from the manufacturer with pre-installed gimbal flush mounts and we...
What Makes Our Rod Holders The Best?
When you purchase a Cisco rod holder you don't just receive a product, but a promise! We are so confident in...
The cradle style rod holders are designed to index 360° with 20 interlocking positions by simply lifting and turning our exclusively engineered spring...
We have developed a very unique system which makes using the Down East Salty rod holders very versatile and user friendly. We have mounting options available...
February 6, 2017
Orders being placed right now may take 2 weeks to ship due to high order volume. Paying for the expedited shipping will only speed up your shipping once the item is shipped...this will not expedite the day in which the order is packaged for shipment....
January 9, 2017
Every year we look forward to traveling around the Great Lakes and beyond to catch up with our existing satisfied customers and meet new ones! Every product which we manufacture will be on display for any angler to sample and interact with as well as...
Connect With Us
Facebook Cisco Twitter YouTube

1791 East 38th Street, 1A
Cleveland, Ohio 44114
Phone: 216-881-4559
Fax: 216-881-4507 info@ciscofishingsystemsltd.com

Made in the USA!

Cisco Fishing Systems, Ltd. is a BBB Accredited Business. Click for the BBB Business Review of this Fishing Tackle - Wholesale & Manufacturers in Cleveland OH